To report a bug that you have discovered in a personality file,
find the file in the database and click on the picture of a bug.
You will then be required to input your details and information
about the bug.
Please ensure that you are using the most recent version of the personality file before reporting a bug.
| Fixture Details | Desk Type | Bug Info | Status | Report Date |
|---|---|---|---|---|
PLS
|
Titan Mobile (.d4) |
Spot PLS 150W Colours Open=White Colour 1=Red Colour 2=Green Colour 3=Yellow Colour 4=Blue Colour 5=Purple Colour 6=Orange Colour 7=Cyan If you can fix the colours before the Christmas Shutdown i will be pleased |
Requested |
21/12/2024 14:11:10 |
Uplus Lighting
|
Titan Mobile (.d4) |
Swatch Imaged on GOBO 1 are in incorrect Order. Correct order is: 1 = image of G2 2= G3 3= G1 4= G6 5= G4 6= G6 correct 7= g7 correct |
Requested |
20/12/2024 17:13:29 |
Shehds
|
Titan Mobile (.d4) |
Visualizer issue... the beam angle for the RGB section is full 180 degrees and is difficult to use in this manner please narrow beam to 90 degrees fixture is a bee eye that zooms into a narrow beam so 90 degrees would be a nice medium since the bee eye effect can't be shown |
Dormant |
04/07/2024 23:33:55 |
Sagitter
|
Quartz (.d4) |
Buongiorno, da parte di Sagitter Club 7 R 230 W a 16 CH Ho trovato un errore mi potete aiutare ? Problema Pan e Tilt, ho provato con un mixer analogico e risulta : Pan Hight 10 Pan Low 11 Tilt Hight 12 Tilt Low 13 Questa � la configurazione corretta, altrimenti quando muovo encoder del Tilt sulla Quartz non risponde. Dispongo di una Quartz QTZ-04161 Grazie Fernando |
Being Fixed |
05/11/2023 06:43:29 |
Uplus Lighting
|
Titan Mobile (.d4) |
Basic, 21 &Extended, 29 DMX When using DMX, Dimmer does not reach 100%. It lights up at 100% when lowered to 99.81%. |
Requested |
17/10/2023 05:50:23 |
Uplus Lighting
|
Titan Mobile (.d4) |
Basic, 21 When using DMX, Dimmer does not reach 100%. It lights up at 100% when lowered to 99.81%. |
Requested |
17/10/2023 05:22:43 |
High End
|
Diamond 4 (.d4) |
seem that the channel output is correct, however the capture model puts out the wrong CMY colours. I think tis is just a capture model fault. |
Requested |
03/01/2021 16:55:30 |
Robe
|
Diamond 4 (.d4) |
Hello, in mode 1 (34 ch), Tetra2 doesn't respond to Grand Master in Capture 2020. Dimmer and Master Dimmer have a wrong response. Only Master Dimmer work. Zooms are the same problem. Master zoom OK. Zoom 1 and Zoom 2 doesn't work. When I clear, Dimmer is at 0%, Master Dimmer stay at 100% and the fixture stay light on in Capture. I've tested the 6 modes, anyone work wrong with zoom 1 and zoom 2. Only Master Zoom respond. |
Requested |
24/12/2020 13:32:18 |
Laserworld
|
Quartz (.d4) |
Hi In dj mode it uses 19 ch and not 11 as your profile is made. You probably forgot to read page 2 (ch 12 to 19) Link to the lamp https://www.laserworld.com/en/support/downloads/download/83-laserworld-diode-series/1888-laserworld-manual-ds-1000rgb-ds-2000rgb-ds-3000rgb-2020-02 .html The channels can be viewed on pages 16 and 17. |
Requested |
01/05/2020 19:49:19 |
JB Systems
|
Pearl 2000/2004 (.R20) |
9 Special Control Speed 100% not correct, yoke is reset by use LOC LOC ch 9 = need to set on 0%. 100% = reset also for the other dmx mode 9 & 11 ch |
Requested |
13/03/2020 10:33:54 |
Wonsung
|
Diamond 4 (.d4) |
Gobo's in incorrect order, fixture locates to gobo 1 instead of open. Correct order should be Gobo1, Gobo2, Gobo3, Gobo4, Open, Gobo5, Gobo6, Gobo7 Manual for 12 and 8 Channel at dropbox link below: https://www.dropbox.com/s/2iowyz5qhxdv7h8/Wonsung%2080w%20Spot%20Light%20Manual.pdf?dl=0 |
Requested |
10/02/2020 14:58:49 |
High End
|
Diamond 4 (.d4) |
see http://forum.avolites.com/viewtopic.php?f=7&t=6017 It occurs that the CMY channels are inverted in capture - you need to invert them in Titan, in order to get output when pressing locate. Unfortunately the manual doesn't give away how these channels are supposed to work, but I have reason to assume these channels need to be un-inverted in capture/AtlaBase. Don't know if you have a fixture to test this - and then, please have AtlaBase correct this |
Requested |
17/02/2019 03:30:53 |